A serious error occurs when data is encrypted to update an encryption key with the HDD encryption unit. An error is detected on the wireless LAN thẻ (802.11a/g, g or Bluetooth). Due to a control error, a RAM overflow occurred during system processing. One of the following messages was displayed on the operation panel.
The “floating” (non-contact) thermistor at the center of the heating roller is not operating correction. Used toner cannot be transported to the used toner bottle. The motor cho thue may photocopy hai phong is trying to rotate at power on or during normal operation but there is an excessive load on the drum shaft. After the M, C, or Y drum started to rotate, the feedback for the charge unit of the color dropped below 0.3V.
Transfer Output Error A high voltage feedback voltage of less than 0.5 V was detected for 200 ms. Scanner Lamp Error At power on the scan lamp trigger remained off. Power requirements are based on the country/region where the printer is sold. This will damage the printer and void the product warranty.
While the polygon motor is rotating normally, no synchronizing detection signal is output for LD0 black, or leading edge, even after the laser diode has been firing for 2 sec. The machine detects an electronic license error in the application on the SD thẻ in the controller slot immediately after the machine is turned on. The program on the SD thẻ contains electronic confirmation license data. The paper position sensor moves but is not detected at the home page position within the specified time.
1st tray lift malfunctionThe tray lift sensor is not activated after the tray lift motor has been on for 10 seconds. If the main power switch is turned on when the paper is already at the feed height, the paper height position is detected again. At this time, the tray lift sensor should de-activate within 1.5 sec after the paper bottom plate starts to drop. If it does not deactivate within 1.5 sec., a message will prompt the user to reset Tray 1. After two attempts to release the error by re-setting the paper tray, if this does not solve the problem then this SC is displayed.
• Check the ID sensor harness and connector. The punch unit moves but is not detected at the home position within the specified time. The fusing sensor detected a fusing unit paper late jam three times. The paper was late and the fusing exit sensor could not detect the paper three times. • The zero cross signal is detected three times even though the heater relay is off when turning on the main power. • The zero cross signal is not detected for 2 seconds even though the heater relay is on after turning on the main power or closing the front door.
The folder plate moves but is not detected at the trang chính position within the specified time. The upper tray paper height sensor does not change its status with the specified time after the tray raises or lowers. Read more about cho thue may photocopy hai phong here. • After startup reset of the operation panel, the attention code or the attention acknowledge code is not sent from the controller within 15 seconds. • After the controller issues a command to chec the communication line with the controller at 30-second intervals, the controller fails to respond twice.
• Clean or replace the corona wire. • Check the CGB power pack fuse, connection. The address book data cannot be read from the HDD, SD thẻ or flash ROM on the controller where it is stored, or the data read from the truyền thông is defective. The shift motor HP sensor does not detect any change for 1.86 seconds after the shift motor has turned on at power on or during its operation.
The punch HP sensor is not activated within the specified time after the punch motor turned on. An error was detected in the operation of the lift motor for Tray 1 . • Pressure roller thermistor harness loose, disconnected, defective • Pressure roller thermistor defectives. The machine checks for the presence of the K STC and the checks the status of the K image transfer roller lift sensor after the door is closed. • Harness to polygon motor drive board disconnected, defective • Polygon motor defective • Polygon motor drive board defective • Polygon motor defective. Correct the position of the thermistor on the hot roller.
The lock signal remained HIGH for 5 sec. while the người hâm mộ in the development unit was operating. ITB encoder sensor error The ITB sensor that reads the encoded film strip on the edge of the image transfer belt is sending is operating correctly. The lock signal from the paper transfer motor was not detected within 1 sec. after the motor switched on. The PTR was not detected at the home position within 2 sec. after the PTR lift motor turned on.
HDD status codes are displayed below the SC code. An internal application error was detected and operation cannot continue. • Incorrect updating for the system firmware • Defective flash ROM on the controller board Replace the controller board. An error is detected on the HDD immediately after the machine has been turned on, or power has been turned off while the machine has used the HDD.
Vpl could not be adjusted to within +-5V of the target Vpl after exposure of the ID sensor patterns. The development potential of the drum before exposure cannot be adjusted to within +-8 V of the target voltage (-900V). Development gamma for Black, magenta, cyan, or yellow is not within range (0.3 to 6.0). Process control halts when this SC is issued.
The tray lift sensor is not activated after the tray lift motor has been on for 10 seconds. At this time, the tray lift sensor should de-activate within 1.5 sec. after the paper bottom plate starts to drop. If it does not deactivate within 1.5 sec., a message will prompt the user to reset Tray 2. After two attempts to re-set the paper tray, if this does not solve the problem then this SC is displayed.
Phu Son launched a professional copier rental service in Bac Ninh with 100% of all Refurbished copiers with full boxes. • SD card not inserted correctly • SD thẻ defective • Controller board defective • To reformat the SC thẻ, use SD Formatter Ver 1.1. @Remote Service ID2 Mismatch Error 1 CTL ID2 for the device did not match the ID2 stored in NVRAM.
